Mance Hardware Wire Mesh Industrial Co., Limited.

News

News

Tags

News
Your Location:Home » News

Fence product categories and use

2015-12-25 16:07:23 Hot:

Aka Fence
Material: Low carbon steel wire
Weaving and characteristics: weaving and welding
Usage: for roads, railways, airports, residential area, port, garden, feeding and husbandry of barrier protection.
Features: corrosion, aging, sunscreen, weather and so on. Fence surface corrosion form of electroplating, hot dip, spray, dip.
Effect:
⑴ reasonable structure, function excellent.
⑵ in harmony with the landscape, beauty of form.
Embalmed:
After blasting, grinding, passivation, coating, curing and other processes after the plated plastic processing, color is green fruit, coating thickness of 0.5 ~ 0.6mm, powder coated using the preferred anti-aging properties of weather-resistant resin powder imports , the coating must be the same color, smooth surface, it does not allow sagging, dropping tumor or excess agglomeration. Plated surface should be seamless, exposed iron and other defects.
Fence Category:
1, the frame fence
2, bilateral wire fence
Welded wire mesh: welded wire mesh metal wire, carbon steel wire should be used, it shall comply with the provisions of GB343 chemical properties of the sheet web, joints should fall less than 4% of the total number of joints; for volume network, any one area. 15 m2 online pads off 4 percent less than this number should be on the total area of ​​the solder joint.
Anti-cast network
Role of bridge anti-cast net: anti-cast bridge network is mainly provided on the main line at the bridge or overpass through separation, to prevent debris falling on the road underneath the bridge lane want to ensure that vehicle safety.
Mainly in the form of structural steel mesh, welded mesh and so on.
The Railway Series
Flat iron fence
Dimensions 1960 × 2790mm Net box: RHS 60 × 40 × 2.5mm, about the pipe 40 × 40 × 2.5mm, intermediate welding steel 40 × 3, the four ribs of 40 × 4 flat steel, length respectively 1000 and 1200mm. Dip mesh surface (green), the required thickness 0.8-1.2mm, coating uniformity, and color, smooth surface, no sagging, trickle, pink bubbles, cracks and other defects. Catchy joints, around two points behind point, weld length 10-15mm; pads under the mouth, about two in the middle a little, weld length of 10-15mm. Strengthening and fully welded square tube between the ribs, which require a solid weld. After welding welding slag removal, weld should be smooth. After welding mesh warping of not more than 8mm.
Angle fence
1, the appearance of size 1750 × 2750mm.
2, the frame with 40 × 25 × 3.0mm made of angle iron
3, mesh having a diameter of 4.0mm or 3.5mm steel welded together.
4, mesh or 75 × 150 50 × 100mm.
5, the connector uses 40 × 55 × 8.0mm iron sheet.
6, should be galvanized metal corrosion dip treatment.
7, isolation fence in the topography of the lot when set, can be renovated into a certain longitudinal ground, using the metal mesh made of angled parallelogram downslope settings, you can adjust the speed and connections column position, the isolation barrier made stepped.
Rectangular tube fence
1. Exterior dimensions of 1700 × 3000mm (column center distance).
2. The frame with 30 × 50 × 2.0mmd moment tubing.
3. The mesh has a diameter of 4.0mm steel welded together.
The mesh 75 × 150mm.
5. Column using 40 × 40 × 2.5mm square column controls established, mesh link plate with 90 degree knuckle, the thickness of 4.0mm steel.
6. The metal mesh should dip galvanized anti-corrosion treatment.
7. The protective fence installed to achieve the "strict, straight, uniform, beautiful", the line closed tightly, not leaving a gap; straight along the road, do not suddenly away suddenly near; protective fence top and bottom longitudinal transition smooth and tidy, not fluctuated; require overall effect is beautiful, to avoid giving the feeling of clutter. Before installation site should be flat, at the bottom of the fence from the ground level by 10cm design, when satisfied, should backfill.

Related